[root@server1.rootbin.dev ~]# smartctl -a /dev/sda
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.C
Device Model: Hitachi HDS721050CLA362
Serial Number: JP8522HR3GYYJV
LU WWN Device Id: 5 000cca 378f11425
Firmware Version: JP2OA50E
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun May 12 15:23:40 2019 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5066) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 96
3 Spin_Up_Time 0x0007 120 120 024 Pre-fail Always - 192 (Average 190)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 69
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 125
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 138 138 020 Pre-fail Offline - 31
9 Power_On_Hours 0x0012 091 091 000 Old_age Always - 66684
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 69
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 680
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 680
194 Temperature_Celsius 0x0002 253 253 000 Old_age Always - 23 (Min/Max 13/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 132
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 70
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 552 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 552 occurred at disk power-on lifetime: 1148 hours (47 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 86 07 95 00 Error: UNC at LBA = 0x00950786 = 9766790
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 e8 80 07 95 40 08 7d+12:15:22.946 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 08 7d+12:15:22.944 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 7d+12:15:22.943 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 7d+12:15:22.939 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 7d+12:15:22.938 SET FEATURES [Set transfer mode]
Error 551 occurred at disk power-on lifetime: 1148 hours (47 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 86 07 95 00 Error: UNC at LBA = 0x00950786 = 9766790
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 e0 80 07 95 40 08 7d+12:15:04.157 READ FPDMA QUEUED
60 38 d8 98 12 59 40 08 7d+12:15:04.023 READ FPDMA QUEUED
60 20 d0 78 12 59 40 08 7d+12:15:03.943 READ FPDMA QUEUED
60 01 c8 ff d7 1d 40 08 7d+12:15:03.911 READ FPDMA QUEUED
60 01 c0 fe d7 1d 40 08 7d+12:15:03.846 READ FPDMA QUEUED
Error 550 occurred at disk power-on lifetime: 1148 hours (47 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 86 07 95 00 Error: WP at LBA = 0x00950786 = 9766790
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 38 18 00 24 5c 40 08 7d+12:14:35.787 WRITE FPDMA QUEUED
60 08 10 80 07 95 40 08 7d+12:14:35.786 READ FPDMA QUEUED
61 08 08 f0 09 00 40 08 7d+12:14:35.785 WRITE FPDMA QUEUED
ef 10 02 00 00 00 a0 08 7d+12:14:35.783 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 7d+12:14:35.782 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 549 occurred at disk power-on lifetime: 1148 hours (47 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 86 07 95 00 Error: UNC at LBA = 0x00950786 = 9766790
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 80 07 95 40 08 7d+12:14:16.811 READ FPDMA QUEUED
61 08 f0 08 08 00 40 08 7d+12:14:16.809 WRITE FPDMA QUEUED
ef 10 02 00 00 00 a0 08 7d+12:14:16.807 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 7d+12:14:16.806 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 7d+12:14:16.802 IDENTIFY DEVICE
Error 548 occurred at disk power-on lifetime: 1148 hours (47 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 86 07 95 00 Error: UNC at LBA = 0x00950786 = 9766790
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 e8 80 07 95 40 08 7d+12:13:57.974 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 08 7d+12:13:57.864 FLUSH CACHE EXT
61 08 d0 60 18 59 40 08 7d+12:13:57.860 WRITE FPDMA QUEUED
61 08 c8 80 0a 08 40 08 7d+12:13:57.859 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 08 7d+12:13:57.859 FLUSH CACHE EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.